"FLOTON" 2166 T super plasticizer-concrete admixture

"FLOTON" 2166 T super plasticizer-concrete admixture

Product consumption calculator



Product description

FLOTON 2166 Т is naphthalene sulfonate based, high water reduction, super plasticizing (improves concrete flow properties) concrete admixture which increases concrete early and ultimate strength and provides rheoplastic features of the concrete. Conformance code: 04.613/1-А3

The product conforms to the requirements of the AZS 221-2006 (TS EN 934-2) standard, Tables 3.1 and 3.2: “High water reduction, latest generation super plasticizing (improves concrete flow properties) concrete admixture”, and ASTM C 494 Type standard: “High water reduction, latest generation super plasticizing concrete admixture”.

Fields of Application

This concrete admixture can be applied in the following areas:

  • Production of concrete designed for application with or without pumps;
  • Production of wet-spraying concrete;
  • Production of pre-cast and prefabricated concrete (factory manufactured concrete);
  • Areas required early removal of formwork;
  • Production of prestressed concrete with low water/cement ratios;
  • Production of rheodynamic concrete easily laid in reinforced structures.


  • Reduces amount of water at least by 12% compared to admixture-free concrete;
  • Provides easy pumping and high application quality at lower or the same water/cement ratio and under the same operating conditions compared to admixture-free concrete;
  • Increases early and ultimate strength compared to admixture-free concrete;
  • Increases compression and flexural strength compared to admixture-free concrete;
  • Reduces of period of formwork removal compared to admixture-free concrete;
  • Increases the resistance to erosion reducing separation and sweating features;
  • Increases strength of concrete when exposed to freezing and melting temperatures;
  • Provides easy laying on formwork and reinforcement structures compared to admixture-free concrete;
  • Increases impermeability and hardness of concrete, reduces compression and tension and improves other mechanical properties of concrete;
  • Provides easy placement of concrete in reinforcement structures and with lower vibration demand;
  • Does not contain chlorine.

Application procedures

Preparation of the mixture. Mix the mineral adhesive substances (cement, quartz sand, volcanic cinders, slag) with concrete filler till the mixture is entirely homogeneous. After 50-70% of the total required water amount is added, start to add the FLOTON 2166 T product together with the remained amount of water to the mixture.  To provide homogeneous composition of FLOTON 2166 T mixture mix it vigorously during 60 seconds or during the time period predefined based on the laboratory tests.

Chemical admixtures reaction principleThe admixtures react mainly with adhesives. When the admixture is added to the concrete it is absorbed by the adhesive particles. The adhesive particles are repelled from each other under the effect of electrostatic force. Thus, the smaller amounts of water provide the required application conditions. The concrete mechanical strength increases proportionally to the reduction of water content in mixture.

Compatibility to other admixtures. FLOTON 2166 Т may be used together with the following materials:

  • All grades of cement;
  • Self-flow mineral adhesives (quartz sand, volcanic cinders and slag) if required in the cement production process;
  • To increase resistance to freezing and melting temperatures, it may be used together with the AntiAir 250 air entraining admixtures;
  • To prevent water vaporization from mixtures in the concrete composition, and to increase the concrete strength in the areas of hot climate conditions and high air velocity the product may be used together with corresponding moisture-retaining products, likeMA Kur 100, MA Kur 200 and MA Kur 300;

Technical specifications

Composition of product

Naphthalene sulfonate based




1.205-1.225 kg/liter

Chlorine concentration in the composition (EN 480-10)


Alkalies concentration in the composition (EN 480-12)



10 kg cans,

200 kg casks,

1000 kg barrels,

Special transport containers

The parameters have been received at the +200C temperature and 50%  humidity.


It is recommended to add the FLOTON 2166 Т product in proportion of 1.0-2.0% of the cement amount. Depending on the concrete type and characteristics, the actual amount of admixtures should be defined based on the preliminary laboratory tests.

Shelf Life and Storage Method

FLOTON 2166 Т may be stored in original packing in the areas with ambient temperature equal to or above +50C. The product stored in unsuitable conditions and exposed to freezing temperatures should be melted at room temperature without adding water, then it should be mixed using mechanical methods till it gets entirely homogeneous. When mixing compressed air should not be used.

Under the required storage conditions, the product may be stored during 12 months from the manufacturing date. The product in open containers may be used during the entire storage period provided the cap is kept closed.


  • when using the product observe regulations of operational and personnel safety, wear appropriate protective clothing, safety gloves, glasses, and respirators;
  • taking into consideration that the product may cause allergic reactions and itch, take care to avoid contact of its components with skin or eyes, otherwise immediately rinse them with large amount of water and wash with soap;
  • in case you swallow the product, immediately consult a physician;
  • do not keep food in the areas of the product application;
  • keep the product away from children;
  • mix the fine or coarse concrete fillers with mineral adhesives according to the results of laboratory tests (cement, quartz sand, volcanic cinders, slag) till the mixture is completely homogeneous. In case the admixture is added to the dry mixture without water, it will be absorbed by the mixture and will result in forming irregularities when applied. Even if you add water afterwards to such improper mixture, the required type and characteristics of concrete will not be achieved. In case water is added to the mixture in larger amounts than it is required, this will unbalance the required design factors of the concrete, and the required mechanical features of concrete will be deteriorated. Taking into consideration the mentioned above, the concrete admixtures should not be added directly into dry powder mixtures without water;
  • amount of admixture to be added into the mixture composition is calculated as the sum of the weights of cement and adhesives (quartz sand, volcanic cinders, slag) multiplied by the coefficient equal to 0.8-1.4% of the cement amount;
  • in case the amount of product added exceeds the recommended value, the mixture hardening period may increase. In these cases it is necessary to provide the required longer curing time for concrete hardening in the reinforcement structures.

Warranty and technical support

  • information indicated in technical specifications is based on scientific and experimental data;
  • Matanat А company is responsible for the product quality only;
  • with the exception of cases of works executed under the supervision of the company specialists, Мatanat А company shall not be liable for any problems occuring due to improper use of the product by other persons;
  • the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
  • for technical support and/or more information please do not hesitate to contact the Matanat А company!