CONSTRUCTION SYSTEMS

CERAMIC ADHESIVES

JOINT FILLING MIXTURES

REPAIR AND MOUNTING MIXTURES

WATERPROOFING MIXTURES

HEAT INSULATION MATERIALS

PRODUCTS BASED ON GYPSUM

CEMENT-BASED PLASTERS

PRODUCTS BASED ON LIME STONE

LIME PRODUCTS

"MA LİME" hydrated lime alabaster

PVA GLUES

PAINTING PRODUCTS

DECORATIVE FACADE COATINGS BASED MINERAL

"FasMazaik" decorative facade coatings based mineral

PRIMERS

SURFACE PROTECTION AND SURFACE CLEANING

SURFACE SYSTEMS

CEMENT BASED SURFACE HARDENING MATERIALS

SOLVENT-FREE EPOXIDE BASED MATERIALS

"Staltop EX-50" solvent-free epoxide based two-component surface hardener

SELF-LEVELLING FLOOR COMPOUND

ADMIXTURE SYSTEMS

CONCRETE ADMIXTURES

MIXED ADDITIVES

"İzoSem" waterproofing admixture

CONCRETING ASSISTANT MATERIALS

SUPPORTING MATERIALS FOR GRINDING

AUXILIARY PRODUCTS TO CONSTRUCTION OF UNDERGROUND

"MATANAT FUGA" facade joint filler (1-6 mm)

Product consumption calculator

Preorder

Product Description

Cement based joint filling mixture, enriched with mixtures increasing material quality and resistance to cracks, enhancing potential of the product usage, improving the properties of waterproofing, color retention and smoothness of the surfaces. The product is manufactured in color available at the time of order placement. The product conforms to the requirements of AZS 321-2008 (TSEN 13888) standard.

Fields of Application

This joint filling mixture can be applied in the following areas:

Indoor and outdoor;
Filling of 1-6 mm joints in such facing materials, as granite, different size ceramic, cotto, limestone, glass mosaic;
Filling of joints in facing materials used in places with instant temperature changes, and for floorings in the areas with busy pedestrian flows and heavy vehicles traffic.

Advantages

This joint filling mixture shows high waterproof properties in the areas with instant temperature changes (from warm to cold, and from cold to warm). The mixture is very rigid, does not form cracks, prevents fading of colors, creates smooth and brilliant surface, resistant to freezing conditions.
Easy preparation and use;
Resistant to cleaning operations in the conditions of up to +1500C temperature and 100 bar water pressure.

Method of application

Preparation of surfaces. Please be careful to the surface to be used: it should be firm, dry, clean, and should have required dimensions; the surface should be totally free of oil and paraffin residues deteriorating adhesive force.

Preparation of the mixture. Carefully pour 20kg powder mix to 7.0 –7.4 liters of water and mix till it is entirely homogeneous (to prepare the mixture it is recommended to use slow circulation mixer). Give the mixture 3-5 minutes to set, mix again before application. During mixing keep an eye on the amount of water, do not use if it is too watery. Application of product with excess of water may cause cracks, concaves, quick erosion, dusting and color change.

Application. Spread the mixture over the surface, then fill joints in a criss-cross manner using rubber trowel and strike off extra amounts. Clean the surface using wet sponge in 20-30 minutes. Once dry, treat the surface using coarse chintz to give it brilliance. Prepared mixture should be used within 2 hours. Do not use the mixture after this period expired.

Recommendations. If at the time of application of FugaFas 100 joint filling mixture the environmental temperature exceeds the limits of +50C- +300C range, the required temperature should be provided. The product should not be used in warm (above +300C), rainy and windy weather conditions. After the useful life expiration the mixture in no case should be diluted with water or fresh powder mix. The treated area can be put into operation in 24-48 hours after accomplishment of the filling operations. After use all hand tools and devices should be cleaned with water.

Shelf Life and Storage Method

The product can be stored during 12 months packed in original sacks in dry conditions on wooden racks, maximum 10 sacks per rack.

Warnings

taking into consideration abundance of admixtures in the composition of the powder mix, immediately wash it with water in case of contact with skin or eyes;
when using pay particular attention to cleanliness of the containers;
do not add to the powder mix any substances, with the exception of water.
do not add PVA;
parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

information indicated in technical specifications is based on scientific and experimental data;
Matanat А company is responsible for the product quality only;
with the exception of cases of works executed under the supervision of the company specialists, Мatanat А company shall not be liable for any problems occuring due to improper use of the product by other persons;
the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
for technical support and/or more information please do not hesitate to contact the Matanat А company!