CONSTRUCTION SYSTEMS

CERAMIC ADHESIVES

JOINT FILLING MIXTURES

REPAIR AND MOUNTING MIXTURES

WATERPROOFING MIXTURES

HEAT INSULATION MATERIALS

PRODUCTS BASED ON GYPSUM

CEMENT-BASED PLASTERS

PRODUCTS BASED ON LIME STONE

LIME PRODUCTS

"MA LİME" hydrated lime alabaster

PVA GLUES

PAINTING PRODUCTS

DECORATIVE FACADE COATINGS BASED MINERAL

"FasMazaik" decorative facade coatings based mineral

PRIMERS

SURFACE PROTECTION AND SURFACE CLEANING

SURFACE SYSTEMS

CEMENT BASED SURFACE HARDENING MATERIALS

SOLVENT-FREE EPOXIDE BASED MATERIALS

"Staltop EX-50" solvent-free epoxide based two-component surface hardener

SELF-LEVELLING FLOOR COMPOUND

ADMIXTURE SYSTEMS

CONCRETE ADMIXTURES

MIXED ADDITIVES

"İzoSem" waterproofing admixture

CONCRETING ASSISTANT MATERIALS

SUPPORTING MATERIALS FOR GRINDING

AUXILIARY PRODUCTS TO CONSTRUCTION OF UNDERGROUND

"PENABET" adhesive for aerated concrete blocks

Product consumption calculator

Preorder

Product Description

Nanotechnology cement based gas concrete and/or foamed concrete adhesive, grey color, monocomponent, enriched with mixtures providing high results. Adhesive conforms to the requirements of AZS 039-2000 (TS-11140 - 1993) standard “Adhesives – cement based (hydraulic conjunction), suitable for glazed, ceramic, and floor tiles”.

Fields of Application

This ceramic adhesive can be applied in the following areas:

Adhesive bonding and fabricating of gas concrete blocks, decorative facing bricks, gypsum counter ceiling panels, foamed concrete, and other lightweight materials having low specific weight and high level of moisture absorption.

Advantages

The most effective adhesive that can be used both as masonry-plaster and mixture for filling of joints, and as material for bonding of light-weight tiles to surfaces in the process of laying light-weight construction materials;
Very simple preparation and use;
Resistant to freezing and warm weather conditions.
The most effective adhesive that can be used both as masonry-plaster and mixture for filling of joints, and as material for bonding of light-weight tiles to surfaces in the process of laying light-weight construction materials;
Very simple preparation and use;
Resistant to freezing and warm weather conditions.

Application procedures

Preparation of the surfaces. Please pay attention to the surface to be used before application of construction materials manufactured from foamed concrete and gas concrete: the surface should be sound, dry, clean, and should have required dimensions; the surface should be totally free of fat and paraffin residues deteriorating adhesive force. In case the surface has 5-6 mm deep cracks or pores, they should be filled with Filkret repair mixture the day before use. In addition the surface to be used should first be dampened or primed with Binmader primer.

Preparation of the mixture. Carefully pour 25 kg of powder mix into 6.0 - 6.5 liters of water and mix till it is entirely homogeneous (to prepare the mixture it is recommended to use slow circulation mixer). Give the mixture 3-5 minutes to set, mix again before application.

Application. Apply the equal thickness layer of adhesive both onto the surface of the partially errected wall and onto the lateral sides of materials used to build the wall. In case the lower part has any distortion, repair the initial row using cement-and-sand slurry until it is leveled. Thereafter it is not required to align sequential rows.
Try not to permit the horizontal and vertical joints exceed maximum 3 mm during construction. Take care to fill these joints totally.

Prepared mixture should be used within 3 hours. We do not recommend to use the mixture after this period expired and crust formed.

Recommendations. If at the time of application of PENABET adhesive the environmental temperature exceeds the limits of +50C- +300C range, the required temperature should be provided. The adhesive should not be used in warm (above +300C), rainy and windy weather conditions. After the useful life expiration the PENABET mixture in no case should be diluted with water or fresh powder mix. After use all hand tools devices should be cleaned with water. After hardening the MA kontakt adhesive can be removed from the surface by mechanical means only.

Shelf Life and Storage Method

The product can be stored during 12 months packed in original sacks in dry conditions on wooden racks, maximum 10 sacks per rack.

Warnings

taking into consideration cement base and complex composition of the PENABET adhesive mixture, immediately wash it with water in case of contact with skin or eyes;
do not add to the mixture any substances not mentioned in the method of application;
parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

information indicated in technical specifications is based on scientific and experimental data;
Matanat А company is responsible for the product quality only;
with the exception of cases of works executed under the supervision of the company specialists, Мatanat А company shall not be liable for any problems occuring due to improper use of the product by other persons;
the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
for technical support and/or more information please do not hesitate to contact the Matanat А company!