CONSTRUCTION SYSTEMS

CERAMIC ADHESIVES

JOINT FILLING MIXTURES

REPAIR AND MOUNTING MIXTURES

WATERPROOFING MIXTURES

HEAT INSULATION MATERIALS

PRODUCTS BASED ON GYPSUM

CEMENT-BASED PLASTERS

PRODUCTS BASED ON LIME STONE

LIME PRODUCTS

"MA LİME" hydrated lime alabaster

PVA GLUES

PAINTING PRODUCTS

DECORATIVE FACADE COATINGS BASED MINERAL

"FasMazaik" decorative facade coatings based mineral

PRIMERS

SURFACE PROTECTION AND SURFACE CLEANING

SURFACE SYSTEMS

CEMENT BASED SURFACE HARDENING MATERIALS

SOLVENT-FREE EPOXIDE BASED MATERIALS

"Staltop EX-50" solvent-free epoxide based two-component surface hardener

SELF-LEVELLING FLOOR COMPOUND

ADMIXTURE SYSTEMS

CONCRETE ADMIXTURES

MIXED ADDITIVES

"İzoSem" waterproofing admixture

CONCRETING ASSISTANT MATERIALS

SUPPORTING MATERIALS FOR GRINDING

AUXILIARY PRODUCTS TO CONSTRUCTION OF UNDERGROUND

"FugaBlesk" jewel-effect joint filling mixture

Product consumption calculator

Preorder

Product Description

Decorative, hygienic and easily removable joint filling mixture provides the effect of gold, silver and brass metal, making the areas of its application more attractive creating brilliant (glimmer) appearance due to jewel-effect particles. The product conforms to the requirements of AZS 321-2008 (TSEN 13888) standard.

Fields of Application

This joint filling mixture can be applied in the following areas:

Filling joints in such construction materials as granite, ceramics, mosaic, and other similar materials, on vertical surfaces, in indoor and outdoor applications;
Filling joints in such construction materials as cobbled ceramics, granite, mosaic, artificial slabs, and other similar materials, on horizontal surfaces, in indoor and outdoor applications.

Advantages

Resistant to dirt;
Clean product from hygienic point of view;
Easily removable;
Prevents fading of colors;
Creates decorative and irreplaceable appearance due to jewel-effect admixtures;
Long effective life due to resistance to cracks and erosion;
More attractive comparatively to cement based joint filling mixtures.
Can be used within 50-minute period at 250C temperature;

Method of application

Preparation of the surfaces. The surface to be treated with the product should be dry, and its wetness should not exceed 5% value. The joints should be free of dust, dirt and construction particles, at least 2/3 part should be empty. To make the jewel effect more attractive it is recommended that the joint width should be at least 3mm. At low temperatures the product shows high level of thickening. Due to this reason the temperature in working premises should be kept at the required level (+230C±30C) for 1 (one) day before application of the product. Prior to beginning the work certainly put on protective gloves and glasses.

Preparation of the mixture. At the time of Preparation of the mixture remove the Components A, B, C, and D from their containers and put them aside, then place the full amounts of the Components A, B, and D sequentially into one container and mix them using slow circulation mixer till the mixture is entirely homogeneous. Be careful mixing the Component D, as it is very light and volatile. To obtain lustreless appearance the mixture can be prepared without addition of Component D. Then add the C Component into the obtained mixture and mix by the same procedure till it is homogeneous.

Application. Fill the joints in a criss-cross manner using elastic trowel. Strike off extra amounts using the elastic trowel. Clean the surface and joints from the contaminations in 15 minutes after application of FugaBlesk mixture using wet sponge soaked with cold water in the manner of light angular motion. In 24 hours remove the remained contaminations from the surface using coarse chintz. To provide full cleaning of the surface repeat the last operation using vinegar in water solution or acetone.

Recommendations. Do not mix the product with any additional admixtures not indicated in operation instructions. The prepared mixture should be used within 50-minute period at 250C temperature. The effective life period can be affected by environmental and surface temperatures. At high temperatures the effective life of the product increases, and at low temperatures the effective life period decreases. After the useful life expiration the prepared mixture should not be used.

Shelf Life and Storage Method

The product can be stored during 12 months packed in original sacks in dry conditions at ambient temperatures between +50C and +350C.

Warnings

certainly use protective gloves and glasses during product application;
taking into consideration abundance of admixtures in the composition of the product, immediately wash it with water in case of contact with skin or eyes;
do not add to the powder mix any substances, not indicated in the operation instructions;
light color products can turn darker in case of outdoor application and exposure to ultraviolet radiation;
in case the color of the FugaBlesk jewel-effect particles fades during cleaning works involving strong cleansers, remove the tarnish by means of pH neutral cleaning agents (soap with water mix);
parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

information indicated in technical specifications is based on scientific and experimental data;
Matanat А company is responsible for the product quality only;
with the exception of cases of works executed under the supervision of the company specialists, Мatanat А company shall not be liable for any problems occuring due to improper use of the product by other persons;
the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
for technical support and/or more information please do not hesitate to contact the Matanat А company!