CONSTRUCTION SYSTEMS

CERAMIC ADHESIVES

JOINT FILLING MIXTURES

REPAIR AND MOUNTING MIXTURES

WATERPROOFING MIXTURES

HEAT INSULATION MATERIALS

PRODUCTS BASED ON GYPSUM

CEMENT-BASED PLASTERS

PRODUCTS BASED ON LIME STONE

LIME PRODUCTS

"MA LİME" hydrated lime alabaster

PVA GLUES

PAINTING PRODUCTS

DECORATIVE FACADE COATINGS BASED MINERAL

"FasMazaik" decorative facade coatings based mineral

PRIMERS

SURFACE PROTECTION AND SURFACE CLEANING

SURFACE SYSTEMS

CEMENT BASED SURFACE HARDENING MATERIALS

SOLVENT-FREE EPOXIDE BASED MATERIALS

"Staltop EX-50" solvent-free epoxide based two-component surface hardener

SELF-LEVELLING FLOOR COMPOUND

ADMIXTURE SYSTEMS

CONCRETE ADMIXTURES

MIXED ADDITIVES

"İzoSem" waterproofing admixture

CONCRETING ASSISTANT MATERIALS

SUPPORTING MATERIALS FOR GRINDING

AUXILIARY PRODUCTS TO CONSTRUCTION OF UNDERGROUND

"ŞPAK-F" fine facing paste

Product consumption calculator

Preorder

Product description

Lime stone based, monocomponent, white color, facing paste, designed for building facades and indoor areas.

Fields of Application

This product can be applied in the following areas:

on vertical surfaces indoor and outdoor;
repair of holes, cavities and cracks on surfaces;
on the surfaces plastered with cement based plaster;
on the surfaces lined with CPF (compressed polystyrene foam), EPF (extruded polystyrene foam), rock-wool (pressed mineral cotton panels) and polyurethane panels;

Advantages

the product has high bonding properties;
resistant to ultraviolet radiation and frost;
does not form cracks on the walls due to its elastic nature;
ultimately resistant to rain, humidity and moisture;
provides long-term protection from discoloration for paints;
environmentally friendly;

Application procedures

Preparation of the surface. Before application of the FasNatural product pay attention to the surfaces: they should be checked for strength, and free of residues deteriorating adhesive force. In case

Application conditions

The surface. The surface should be clean, healthy and wet. In case the treated surface has any defects and cracks 3mm deep and deeper, they should be repaired using MATON repair mixture at least 72 hours before the Şpak-F application. Prior to the application of the product the surface should be dampened and primed with BINMADER primer

Preparation of the mixture. Carefully pour 20 kg of Şpak-F product into 7.5 – 8.0 liters of clean water. Prepare the mixture using trowel or slow circulation manual mixer until the mixture is entirely homogeneous. Wait 3 minutes after mixing and mix again before application.

Application. Apply the mixture to provide equal thickness on the entire surface, using steel trowel. In case more than one layer is required the time interval between layer applications should be 2-3 hours, and the total thickness should not exceed 3 mm. The mixture prepared for application should be used within 4 hours maximum. The mixture should not be used after expiration of useful life.
After the Şpak-F is mixed with water it is mandatory required to strictly observe the waiting time, and to mix again before application. Do not add any materials (lime, cement, gypsum, etc) to the prepared mixture. The surface should be dampened during 2-3 days after application of the mixture, and should be polished after complete hardening.

Recommendations. If at the time of the Şpak-F product application the ambient temperature exceeds the limits of +50C - +300C range, then the required temperature level should be provided. The product should not be applied onto the surfaces located in warm (above +300C), and very windy, or in 24-hour frosty weather conditions. The product should not be applied after expiration of useful life. After use all hand tools and devices should be cleaned with water.

Consumption

Depending on the surface, the mixture consumption for 1 m2 of surface is 0.8 -1.0 kg (at 1 mm thick layer).

Shelf Life and Storage Method

The product can be stored during 12 months from the manufacturing date, in dry conditions, on wooden racks, maximum 10 sacks per rack.

Warnings

pay special attention to clean conditions of the cans and water used during preparation of Şpak-F mixture;
do not add to the mixture any chemical substances;
parameters indicated above have been received on the basis of laboratory tests conducted in the ambient conditions of +230C±20C temperature and 50% + 5% humidity. Depending on the actual ambient conditions these parameters are subject to change.

Warranty and technical support

information indicated in technical specifications is based on scientific and experimental data;
Matanat А company is responsible for the product quality only;
with the exception of cases of works executed under the supervision of the company specialists, Мatanat А company shall not be liable for any problems occuring due to improper use of the product by other persons;
the company reserves the right to make changes in its product in consequence of scientific-and-technical development;
for technical support and/or more information please do not hesitate to contact the Matanat А company!